How to connect 1 router, 2 switches and 4 pc in Cisco packet tracer

How to connect 1 router, 2 switches and 4 pc in Cisco packet tracer, how to make it as below.
1. First click Router0
2.Click Switch0
3.Connect Router0 with Switch0 using straight cable or can use automatic cable (how to connect with Router0 as FastEthernet0 / 0 while Switch0 as Fastethenet 0/1)
4.Click Switch1
5.Connect Router0 with Switch1 using straight cable or can use automatic cable (how to connect with Router0 as FastEthernet0 / 1 while Switch1 as Fastethenet 0/1)
  later will be like the picture below:

then setting Router0 first First we will do the settings on Router0 and settings like this:
1.klik Router 0
2.Click config
3.Click fastethernet 0/0 (we click on fastethernet0 / 0 because this is used for connection Switch0 with Router0)
4. Check the Status Port to ON
5.Isi IP Address with 192.168.1.1 and click to subnet mask column then automatically will come out number 255.255.255.0
if true then the settings are like this picture

 and there will be a green image like in the picture above, then setting up Router0 again, for setting fastehtenet0 / 1 which connects to Switch1 and the way as below
1.klik Router 0
2.Click config
3.Click fastethernet 0/1 (we click fastethernet0 / 1 because this is used for connection Switch1 with Router0)
4. Check the Status Port to ON
5.Isi IP Address with 168.168.1.1 and click to subnet mask column then automatically will come out number 255.255.0.0
if true then the settings are like this picture

if you have set up Router0, then just add 2 pc on the left side of switch0, and add 2 pc on the right side switch1, as shown below:

 in the picture above PC0 and PC1 are on the left Switch0, while PC2 and PC3 are on the right side of Switch1, after we make the picture above, we just fill the IP Address and also Default Gateway from each PC.
First we will Set Up IP Address and Default Gateway from the left side of Swicth0 ie PC0 and PC1

For PC0:
IP Address: 192.168.1.2 (According to the Fastethernet IP Address 0/0 ie 192.168.1.1 but changed its last number to 2)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1 (As per IP address fastethernet 0/0 ie 192.168.1.1)

For PC1:
IP Address: 192.168.1.3 (As per IP address fastethernet 0/0 ie 192.168.1.1 but changed its last number to 3)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1 (As per IP address fastethernet 0/0 ie 192.168.1.1)

 Next we will Set the IP Address and Default Gateway from the right side of the Swicth1 PC2 and PC3

For PC2:
IP Address: 168.168.1.2 (As per the IP Address fastethernet 0/1 is 168.168.1.1 but changed its last number to 2)
Subnet Mask: 255.255.255.0
Default Gateway: 168.168.1.1 (As per IP Address fastethernet 0/1 is 168.168.1.1)

For PC3:
IP Address: 168.168.1.3 (As per IP address fastethernet 0/1 is 192.168.1.1 but changed its last number to 3)
Subnet Mask: 255.255.255.0
Default Gateway: 168.168.1.1 (As per IP Address fastethernet 0/1 is 168.168.1.1)

 After you have finished all of them, you just ping pc, first will fail first but after that will succes on second ping

Explanation:


     First Connection between Switch and Router must be correct, ie fast ethernet0 / 0 connection for left switch0 and fast ethernet 0/1 for right switch1. Both IP addresses in routers that are in fastethernet 0/0 with fastethernet 0/1 must be different ie 192.168.1.1 with 168.168.1.1, all three IP addresses in fast ethernet 0/0 are used to defaul gateway on pc left part and also for IP address pc but the last number should be different eg default gateway 192.168.1.1 then the IP address for pc 192.168.1.2, while the IP address in fastethernet 0/1 is used for the default gateway on the right pc, and IP address on the PC, the last digit is also replaced, default gateway 168.168.1.1 then the IP address for pc 168.168.1.2, Fourth when the first ping will fail but when the second ping will success.

 download the file can be below:
Download 
That's how to connect 1 router, 2 switches and 4 pc in Cisco packet tracer, thanks for reading.

How to connect 2 routers with 2 pc in Cisco Packet Tracer

How to connect 2 routers with 2 pc in Cisco Packet Tracer, do as follows:
1.Click Router0
2.Click Router1
3.Connect Router0 with Router1 using crossover cable or can use automatic.Router0 as FastEthernet 0/0, and Router1 Also as FastEthernet 0/0, like the picture below

 After creating according to the picture above we continue to set Router0 and also router1 is as follows:
1.Click Router0
2.Click Config
3.Click FastEthernet 0/0
4. Check Port Status Being ON
5.Isi IP Address with 192.168.1.1, then when the click to subnet mask will exit 255.255.255.0
as shown below:

After making according to the picture above we continue to set Router1 that is as follows:
1.Click Router1
2.Click Config
3.Click FastEthernet 0/0
4. Check Port Status Being ON
5.Isi IP Address with 192.168.1.2, then when the click to subnet mask will exit 255.255.255.0

after the corresponding image above then add the pc to the left of Router 0 and the right Router1 in this way:
1.Click PC0
2.Connect PC0 with Router0 using a crossover cable (router0 as FastEthernet 0/1)
3.Click PC1
4.Connect PC1 with Router1 using a crossover cable (router1 as FastEthernet 0/1)
  as shown below

after matching the picture above then we set the Router0 for PC0, as below:
1.Click Router0
2.Click Config
3.Click FastEthernet 0/1
4. Check Port Status Being ON
5.Isi IP Address with 192.168.2.1, then when the click to subnet mask will exit 255.255.255.0
as shown below

Once it is appropriate above, then setting up RIP
6. Click Rip
7.Isi Network 192.168.1.1 in add, then fill the Network again 192.168.2.1 then in add (ip used in accordance IP in FastEthernet 0/0 and FastEthernet 0/1)
after finished will be like the picture below

 after matching the image above, then setting up IP address PC0 with settings like below:
IP Address: 192.168.2.2
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.2.1 (matches ip address in FastEthernet 0/1 in router0)

after you set up Router0 and PC0, then we set Router1 and PC1 in this way:
1.Click Router1
2.Click Config
3.Click FastEthernet 0/1
4. Check Port Status Being ON
5.Isi IP Address with 192.168.3.1, then when the click to subnet mask will exit 255.255.255.0
as shown below:

 Once it is appropriate above, then setting up RIP
6. Click Rip
7.Isi Network 192.168.1.2 in add, then fill the Network again 192.168.3.1 then in add (ip used in accordance IP in FastEthernet 0/0 and FastEthernet 0/1)
when finished will be like the image below:

after matching the image above, then setting up IP address PC1 with settings like below:
IP Address: 192.168.3.2
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.3.1 (matches ip address on FastEthernet 0/1 in router1)

after doing all that, we just do Ping, do to success

Explanation: Firstly, the IP connecting router with the router must be the same and only differ in the end like this 192.168.1.1 in router0 which is in FastEthernet0 / 0, and 192.168.1.2, in router1 which is in FastEthernet0 / 1. Secondly, we have to using setting up RIP for successful data transmission to ping. Thirdly, Can be seen Here for an explanation of the same meaning as the explanation of this way.

Can download the file below:
Download 

Thanks for reading, that's how to connect 2 routers with 2 pc in Cisco Packet Tracer.

 

Cara Membuat jaringan 1 router linkeys,1router,2switch,5 pc di cisco

Cara Membuat jaringan 1 router linkeys,1router,2switch,5 pc di cisco,sebagai berikut:

Pertama kamu harus membuat sambungan Linkeys router dengan router terlebih dahulu seperti cara dibawah ini:
1.Klik Linkys wireles router0
2.Klik Router 0
3.Sambungkan Router0 dengan Linkeys wireles router0 menggunakan kabel crossover(Router0 sebagai FastEthernet 0/0 sedangkan Linkeys sebagai Internet),seperti gambar dibawah ini:

:

 Setelah sama seperti di gambar,selanjutnya kita mengatur Router0 dan linkeys dengan cara sebagai berikut:
4.Klik Router0
5.Klik Config
6.Klik FastEthernet 0/0
7.Centang port status menjadi ON
8.Isi IP Address 192.168.0.1,dan subnet mask 255.255.255.0
seperti gambar dibawah ini

Setelah itu kita mensetting FastEthernet 0/1 di Router0 dengan cara seperti ini:
9.Klik FastEthernet 0/1
10.Centang port status menjadi ON
11.Isi IP Address 192.168.1.1,dan subnet mask 255.255.255.0
seperti gambar dibawah ini:

setelah selesai mensetting router0,selanjutnya kita mensetting Linkeys dengan cara berikut ini:
1.Klik Linksys
2.Klik Config
3.Klik LAN
4.Isi IP Address 192.168.0.1 dan subnet mask 255.255.255.0 (sesuai IP Address di FastEthernet 0/0 di Router0)
seperti gambar dibawah ini:

setelah sesuai gambar diatas,selanjutnya kita mensetting internet dengan cara sebagai berikut:
5.Klik Internet
6.Klik Static
7.Isi Default Gateway dengan 192.168.1.1(sesuai IP Address di FastEthernet 0/1 di Router0)
8.Isi Ip Address dengan 192.168.1.1 dan subnet mask 255.255.255.0(sesuai IP Address di FastEthernet 0/1 di Router0)
seperti gambar dibawah ini:

setelah sesuai gambar diatas selanjutnya kita tinggal menambahkah 1 switch di kiri Router0 dan 1 Switch di kanan Linksys,seperti gambar dibawah ini:

setelah sesuai gambar diatas selanjujutnya kita tinggal menambahkan 2PC di Swicht0, 2PC di Swicht1 dan 1 PC diatas linksys,seperti gambar dibawah ini:

setelah sesuai gambar diatas kita tinggal mensetting IP address dari masing-masing PC,yaitu sebagai berikut
PC0
IP Address:192.168.0.1(sesuai IP address pada LAN linksys)
Subnet Mask:255.255.255.0
Default Gateway:192.168.1.1(sesuai IP Address pada FastEthernet 0/1 dan IP Address pada Internet linksys)

PC1
IP Address:192.168.0.2(sesuai IP address pada LAN linksys beda angka akhir saja)
Subnet Mask:255.255.255.0
Default Gateway:192.168.1.1(sesuai IP Address pada FastEthernet 0/1 dan IP Address pada Internet linksys)

PC2
IP Address:192.168.0.3(sesuai IP address pada LAN linksys beda angka akhir)
Subnet Mask:255.255.255.0

PC3
IP Address:192.168.0.4(sesuai IP address pada LAN linksys beda angka akhir)
Subnet Mask:255.255.255.0

PC4
Disetting terlebih dahulu seperti Cara menyambungkan Wireles Router Linkeys dengan PC via nirkabel di Cisco ,gunakan DHCP

Setelah semua sesuai dengan cara diatas,selanjutnya melakukan RIP pada Router0 caranya seperti dibawah ini:
1.Klik Router0
2.Klik Config
3.Klik RIP
4.Isi network dengan 192.168.0.1 lalu di add,dan isi lagi dengan 192.168.1.1 lalu di add,seperti gambar dibawah ini:

setelah selesai kita hanya tinggal melakukan ping antar pc,biasanya hanya 2 kali ping di pc yang sama maka akan sukses.
Kamu bisa download file pkt dari sambungan ini dibawah ini:
Download
itu dia Cara Membuat jaringan 1 router linkeys,1router,2switch,5 pc di cisco
Terima Kasih Atas Perhatiannya,semoga berhasil.

Cara memberi Security pada wireless di cisco

Sebelum memberi security system pada wireless linkeys,sebaiknya kamu sudah tahu dulu cara membuat jaringan wireles linkeys dengan PC secara nirkabel,kamu bisa melihat Cara menyambungkan Linkeyss wireless via nirkabel ,setelah sudah membuat jaringan tersebut,kita tinggal memberi security pada wireless linkey,yaitu dengan cara dibawah ini:
1.Klik wireless linkeys
2.Klik config
3.Klik wireless
4.ubah disable menjadi WPA2-PSK dengan cara mengkliknya
5.isi SSID dengan pass(ini untuk nama dari wireless)
6.isi dibawah WPA2-PSK dengan tulisan pass1234(ini untuk password dari wireless)seperti gambar dibawah ini:

Setelah selesai kamu tinggal menyambungkan PC0 dengan wireless dengan cara:
1.Klik PC0
2.Klik Dekstop
3.Klik PC Wireless
4.Klik Connect
5.Klik Refresh dan akan seperti gambar dibawah ini:

6.Klik tulisan pass(ini merupakan nama wireles yang kamu buat tadi)
7.Klik connect yang sebelah kanan refresh
8.Isi password pass1234(ini merupakan password yang kamu buat tadi)
9.Klik connect,setelah itu akan tersambung seperti dibawah ini:

itu dia cara memberi security pada wireless di cisco

Cara menyambungkan Wireles Router Linkeys dengan PC via nirkabel di Cisco

Cara menyambungkan Wireles Router Linkeys dengan PC via nirkabel di Cisco,sebagai berikut:
1.Klik Wireless Router Linkeys
2.Klik PC0
seperti gambar dibawah ini:

setelah sesuai gambar diatas,selanjutnya kita mengatur PC0 agar dapat tersambung dengan Linkeys secara nirkabel,caranya sebagai berikut:
1.Klik PC0
2.Klik Linksys-W
3.Klik tombol merah pada pc,hingga lampu hijaunya mati seperti di gambar dibawah ini:

4.Setelah itu tarik kebawah dan drag  and drop yang berwarna merah ke tempat yang berwana hijau,dan drag and drop lagi yang warna hijau ke arah warna merah tadi seperti gambar dibawah ini :

5.Setelah selesai nanti akan seperti gambar dibawah ini:

6.Setelah selesai,tinggal klik tombol power merah lagi hingga hidup berwarna hijau(untuk menghidupkan komputer)
7.Setelah itu tinggal klik dekstop
8.Klik IP Configuration
9.Ubah Static menjadi DHCP
10.Setelah selesai akan seperti gambar dibawah ini:

11.Selanjutnya tinggal melakukan ping dan akan success

Kamu juga bisa download filenya dibawah ini:
Download

Itu dia Cara menyambungkan Wireles Router Linkeys dengan PC via nirkabel di Cisco

Cara menyambungkan Wireles Router Linkeys dengan PC menggunakan kabel Straight di Cisco

Cara menyambungkan Wireles Router Linkeys dengan PC menggunakan kabel Straight di Cisco,sebagai berikut:
1.Klik Wireless Router Linkeys
2.Klik PC0
3.Sambungkan Wireless Router Linkey dengan PC0 menggunakan kabel Straight (wireless router linkeys sebagai Ethernet1,dan PC0 sebagai FastEthernet)
seperti gambar dibawah ini:

setelah seperti gambar diatas,selanjutnya mengatur Wireless Router Linkeys,dengan cara seperti ini:
1.Klik Wireless Router Linkeys
2.Klik Config
3.Klik Internet dan klik static,seperti gambar dibawah ini:

setelah sesuai dengan gambar diatas,selanjutnya mengatur PC0 seperti di bawah ini:
1.Klik PC0
2.Klik.Dekstop
3.Klik IP Configuration
4.Klik DHCP(Maka secara otomatis akan terisi sendiri)

Setelah selesai kamu hanya tinggal melakukan ping antara Linkeys dengan PC maka akan success
kamu juga bisa download file dibawah ini:
Download
itu dia Cara menyambungkan Wireles Router Linkeys dengan PC menggunakan kabel Straight di Cisco,terima kasih sudah mau membaca